WAZER Main Unit Size
WAZER Main Unit Size with Stand Leg Accessory
WAZER Main Unit Empty Weight
WAZER Main Unit Loaded Weight
Pump Box Size
Pump Box Weight
WAZER Specifications
WAZER Main Unit, Leg Stand Accessory, Pump Box
Size and Weight
34” x 25.5”” x 22” (856mm x 648mm x 551mm)
34” x 25.5”” x 48” (856mm x 648mm x 1220mm)
110 lbs. (50 kg)
400 lbs. (180 kg)
21” x 15” x 11” (533 mm x 355 mm x 280 mm)
92 lbs. (42 kg.)
Cutting
Cutting Area
Cut Bed Size
Kerf (width of cut)
12” x 18” (305 mm x 460 mm)
13” x 19” (330 mm x 485 mm)
.044 (1.2 mm)
Water
Water Source
Input Water Filter
Input water requirement
Water Draining
Draining Hose requirement
Water Recirculation
Filtered tap water
~300 mesh
>1gal(3.8L)/min; > 35Psi(2.4Bar) ; TDS<
180mg/L; > 130F/54°C
(1.9L) /min • <30 feet (9m) length; < 4 feet (1.2m) elevation
Not Recommended
Abrasive
Abrasive Flow Rate
Abrasive Capacity
Abrasive Type
40g~150g/min
30lbs (13.5 kg)
Garnet 80 mesh
(If Barton Alltech HPA 80 is not available, please contact WAZER customer support for more information before using alternative brand)
Gantry
Maximum Linear Speed
Gantry Positional Precision
75 IPM (1905 mm/min)
0.003” (0.08 mm)
Power
Main Unit V1.5 (110 VAC and 220 VAC)
Pump Box V1.5A VAC
Pump Box V1.5B VAC
100-240 VAC, 50/60Hz, 2.5A
110-120 VAC; 60Hz; 15A; 1700W
220-240 VAC; 50Hz; 10A; 2200W
Wam Software
Browser Compatibility
Chrome, Internet Explorer, Safari, Firefox
Miscellaneous
Compatible File Types
Connectivity
Noise Emission
Noise Pressure Level
Storage Condition
Maximum Working Pressure & Flow Rate
.dxf, .svg
SD Card
74 + / - 3dB
87 + / - 3dB
0°C - 40°C / 32°F-104°F for prolonged storage
0°C - 70°C / 32°F-160°F for 24 hours
4600psi (32Mps) at 0.5 gal/min (1.9L/min)
Machine System Schematics
Main Unit Control System Diagram
The above illustration shows the high level system schematic of the WAZER V1.5 Main Unit’s electro-mechanical components and controls system.
Pump Box Electronics Layout Diagram
The above illustration shows the high level system schematic of the Pump Box V1.5 wiring and electro-mechanical components.
Hydraulic System Diagram
The above illustration shows the high pressure and low pressure hydraulic system diagrams with relevant components.
Abrasive Usage
Project Abrassive Usage
The materials listed were cut with WAZER using abrasive particles (garnet) at a rate of 0.33lb (0.15kg) per minute. WAZER uses garnet, made specifically for waterjets, which must be continually purchased in order to operate the machine. Abrasive will be available for purchase on our website, but WAZER will also work with approved third party suppliers. WAZER cannot engrave or etch your parts. It is designed for thru-cutting only. Trying to etch with waterjet cutting puts a lot of wear and stress on the internal components and will void your warranty.
Project
Materials Cut by WAZER
Cut Time
Abrasive Usage
Cut Cost
(with 2,200 lb. Abrasive Pallet, Nozzle and Cut Bed 3-Pack
Cut Cost
(with 55 lb. Abrasive Bucket, Nozzle and Cut Bed 1-Pack)
Glass Sculpture
Stained Glass (0.125") (x3)
34 min
11 lbs
$5.44
$17.34
Penny Necklace
Penny (x50)
60 mins
20 lbs
$9.60
$30.60
Project Abrassive Usage
The materials listed were cut with WAZER using abrasive particles (garnet) at a rate of 0.33lb (0.15kg) per minute. WAZER uses garnet, made specifically for waterjets, which must be continually purchased in order to operate the machine. Abrasive will available for purchase on our website, but WAZER will also work with approved third party suppliers. WAZER cannot engrave or etch your parts. It is designed for thru-cutting only. Trying to etch with waterjet cutting puts a lot of wear and stress on the internal components and will void your warranty.
Glass Sculpture
Materials Cut by WAZER
Cut Time
Abrasive Usage
Cut Cost
(with 2,200 lb. Abrasive
Pallet, Nozzle and Cut Bed 3-Pack)
Cut Cost
(with 55 lb. Abrasive Bucket,
Nozzle and Cut Bed 1-Pack)
Stained Glass (0.125") (x3)
34 min
11 lbs
$5.44
$17.34
Penny Necklace
Materials Cut by WAZER
Cut Time
Abrasive Usage
Cut Cost
(with 2,200 lb. Abrasive
Pallet, Nozzle and Cut Bed 3-Pack)
Cut Cost
(with 55 lb. Abrasive Bucket,
Nozzle and Cut Bed 1-Pack)
Penny (x50)
60 mins
20 lbs
$9.60
$30.60
Custom Tile
Materials Cut by WAZER
Cut Time
Abrasive Usage
Cut Cost
(with 2,200 lb. Abrasive
Pallet, Nozzle and Cut Bed 3-Pack)
Cut Cost
(with 55 lb. Abrasive Bucket,
Nozzle and Cut Bed 1-Pack)
Ceramic Tile (0.375") Quatrefoil Profile (x38)
95 mins
31 lbs
$26.88
$85.86
Custom Knife
Materials Cut by WAZER
Cut Time
Abrasive Usage
Cut Cost
(with 2,200 lb. Abrasive
Pallet, Nozzle and Cut Bed 3-Pack)
Cut Cost
(with 55 lb. Abrasive Bucket,
Nozzle and Cut Bed 1-Pack)
D2 Tool Steel (0.16") Knife Blank (x1)
Copper (0.08") Handle Insert (x2)
Carbon Fiber (0.08") Handle Insert - small (x4)
Carbon Fiber (0.08") Handle Insert - large (x2)
118 mins
39lbs
$30.60
$60.18
Bicycle Belt Drive
Materials Cut by WAZER
Cut Time
Abrasive Usage
Cut Cost
(with 2,200 lb. Abrasive
Pallet, Nozzle and Cut Bed 3-Pack)
Cut Cost
(with 55 lb. Abrasive Bucket,
Nozzle and Cut Bed 1-Pack)
D2 Tool Steel (0.16") Knife Blank (x1)
Copper (0.08") Handle Insert (x2)
Carbon Fiber (0.08")
Handle Insert - small (x4)
Carbon Fiber (0.08")
Handle Insert - large (x2)D2 Tool Steel (0.16") Knife Blank (x1)
Copper (0.08") Handle Insert (x2)
Carbon Fiber (0.08") Handle Insert - small (x4)
Carbon Fiber (0.08") Handle Insert - large (x2)
168 mins
55lbs
$26.80
$85.86
Project Info
The materials listed were cut with WAZER using abrasive particles (garnet) at a rate of 0.33lb (0.15kg) per minute. WAZER uses garnet, made specifically for waterjets, which must be continually purchased in order to operate the machine. Abrasive is available for purchase on our website, but WAZER will also work with approved third party suppliers. WAZER cannot engrave or etch your parts. It is designed for thru-cutting only. Trying to etch with waterjet cutting puts a lot of wear and stress on the internal components and will void your warranty.
Project2
Materials Cut by WAZER
Cut Time
Abrasive Usage
Cut Cost
(with 2,200 lb. Abrasive Pallet, Nozzle and Cut Bed 3-Pack
Cut Cost
(with 55 lb. Abrasive Bucket, Nozzle and Cut Bed 1-Pack)
Custom Tile
Ceramic Tile (0.375") Quatrefoil Profile (x38)
95 mins
31lbs
$15.20
$48.45
Custom Tile
The mosaic features 15 conventional quatrefoils that are each inlayed within a singular surrounding tile - an aesthetic that is only possible with waterjet cutting. The tiles are ⅜” (10mm) thick. In total, the project involved 1 hour and 35 minutes of WAZER cut time and used 31 pounds (14kg) of abrasive. Each pair of quatrefoil and surrounding square (of the same color) came from the same tile, so the width of the grout corresponds to the width of WAZER’s cut.
Glass Sculpture
Stained Glass (0.125") (x3)
34 min
11 lbs
$5.44
$17.34
Glass Sculpture
David designed the Pheonix directly with an X-ACTO knife and paper. He took photos of the paper cuts and the team converted them to .DXF files in Photoshop. The entire project took 34 minutes to cut on WAZER and used 11 pounds (5kg) of abrasive.
Penny Necklace
Penny (x50)
60 mins
20 lbs
$9.60
$30.60
Penny Necklace
Stacey is a jeweler and artist who spends a lot of time hand cutting. She cuts intricate shapes in thousands of individual coins for her work, and has been looking for an automated cutting method so she can save her hands and make more jewelry at a lower cost (right now her necklaces sell for $600!). Other solutions were way too expensive, so WAZER was an obvious choice for her. She’s been one of our earliest fans. Check out more of Stacey's work at www.staceyleewebber.com
Bicycle Belt Drive
Aluminum (0.19") Sprockets (x2)
Aluminum (0.0625") Spacer (x1)
Aluminum (0.0625") Rear Frame Coupler (x1)
168 mins
55 lbs
$26.88
$85.86
Bicycle Belt Drive
Designed and built by Cyclist and WAZER Engineer Christian Moore, this custom belt drive was a longtime dream of Christian’s and finally made possible with the help of WAZER. The belt is quieter than a typical chain and is also cleaner, sleeker and does not rust. Christian could not find the right combination of off-the-shelf parts to make this happen - so he had to go custom, and the result is exactly what he wanted.
Custom Knife
D2 Tool Steel (0.16") Knife Blank (x1)
Copper (0.08") Handle Insert (x2)Carbon Fiber (0.08") Handle Insert - small (x4)
Carbon Fiber (0.08") Handle Insert - large (x2
118 mins
39 lbs
$18.88
$60.18
Custom Knife
The knife was made from 4mm-thick D2 tool-steel and the handle from a combination of 2mm copper and carbon fiber sheets. In total the project involved 1 hour 58 minutes of cut time on WAZER a consumed 39 pounds (18kg) of abrasive.
Resources
TIPS & TRICKS
We've learned alot about how WAZER works best. These are our favorite Tips and Tricks.
HOW-TO-VIDEOS
Find all the information you need to safely and properly setup and operate your WAZER.
Materials & Cutting Speed
Still have questions?
Questions about WAZER? Our Sales and Support teams can help answer any question you may have. For more immediate product support, please also review our Resources Section. If you are still having an issue, you can also reach out to the dedicated Technical Support team. We look forward to hearing from you.
Resources
TIPS & TRICKS
We've learned alot about how WAZER works best. These are our favorite Tips and Tricks.
HOW-TO-VIDEOS
Find all the information you need to safely and properly setup and operate your WAZER.
Materials & Cutting Speed
Still have questions?
Questions about WAZER? Our Sales and Support teams can help answer any question you may have. For more immediate product support, please also review our Resources Section. If you are still having an issue, you can also reach out to the dedicated Technical Support team. We look forward to hearing from you.
WAZER Specifications
WAZER Main Unit, Leg Stand Accessory, Pump Box
Size and Weight
WAZER Main Unit Size
WAZER Main Unit Size with Stand Leg Accessory
WAZER Main Unit Empty Weight
WAZER Main Unit Loaded Weight
Pump Box Size
Pump Box Weight
34” x 25.5”” x 22” (856mm x 648mm x 551mm)
34” x 25.5”” x 48” (856mm x 648mm x 1220mm)
110 lbs. (50 kg)
400 lbs. (180 kg)
21” x 15” x 11” (533 mm x 355 mm x 280 mm)
92 lbs. (42 kg.)
Cutting
Cutting Area
Cut Bed Size
Kerf (width of cut)
12” x 18” (305 mm x 460 mm)
13” x 19” (330 mm x 485 mm)
.044 (1.2 mm)
Water
Water Source
Input Water Filter
Input water requirement
Water Draining
Draining Hose requirement
Water Recirculation
Filtered tap water
~300 mesh
>1gal(3.8L)/min; > 35Psi(2.4Bar) ; TDS< 180mg/L; > 130F/54°C
>0.5gal(1.9L) /min; <30 feet (9m) length;
< 4 feet (1.2m) elevation
Not Recommended
Water Source
Input Water Filter
Input water requirement
Water Draining
Draining Hose requirement
Water Recirculation
Filtered tap water
~300 mesh
>1gal(3.8L)/min; > 35Psi(2.4Bar) ; TDS<
180mg/L; > 130F/54°C
(1.9L) /min • <30 feet (9m) length; < 4 feet (1.2m) elevation
Not Recommended
Abrasive
Abrasive Flow Rate
Abrasive Capacity
Abrasive Type
140g~150g/min
30lbs (13.5 kg)
Garnet 80 mesh
(If Barton Alltech HPA 80 is not available, please contact WAZER customer support for more information before using alternative brand)
Gantry
Maximum Linear Speed
Gantry Positional Precision
75 IPM (1905 mm/min)
0.003” (0.08 mm)
Power
Main Unit V1.5 (110 VAC and 220 VAC)
Pump Box V1.5A VAC
Pump Box V1.5B VAC
100-240 VAC, 50/60Hz, 2A, 200W Max
110-120 VAC; 60Hz; 15A; 1700W
220-240 VAC; 50Hz; 8A; 1700W
Wam Software
Browser Compatibility
Chrome, Internet Explorer, Safari, Firefox
Miscellaneous
Compatible File Types
Connectivity
Noise Emission
Noise Pressure Level
Storage Condition
Maximum Working Pressure & Flow Rate
.dxf, .svg
SD Card
74 + / - 3dB
87 + / - 3dB
0°C - 40°C / 32°F-104°F for prolonged storage
0°C - 70°C / 32°F-160°F for 24 hours
4600PSI (32MPa) at 0.5 gal/min (1.9L/min)
Machine System Schematics
Main Unit Control System Diagram
The above illustration shows the high level system schematic of the WAZER V1.5 Main Unit’s electro-mechanical components and controls system.
Pump Box Electronics Layout Diagram
The above illustration shows the high level system schematic of the Pump Box V1.5 wiring and electro-mechanical components.
Hydraulic System Diagram
The above illustration shows the high pressure and low pressure hydraulic system diagrams with relevant components.
Abrasive Usage
Project Info
The materials listed were cut with WAZER using abrasive particles (garnet) at a rate of 0.33lb (0.15kg) per minute. WAZER uses garnet, made specifically for waterjets, which must be continually purchased in order to operate the machine. Abrasive is available for purchase on our website, but WAZER will also work with approved third party suppliers. WAZER cannot engrave or etch your parts. It is designed for thru-cutting only. Trying to etch with waterjet cutting puts a lot of wear and stress on the internal components and will void your warranty.
Project
Materials Cut by WAZER
Cut Time
Abrasive Usage
Cut Cost
(with 2,200 lb. Abrasive Pallet, Nozzle and Cut Bed 3-Pack
Cut Cost
(with 55 lb. Abrasive Bucket, Nozzle and Cut Bed 1-Pack)
Custom Tile
Ceramic Tile (0.375") Quatrefoil Profile (x38)
95 mins
31lbs
$15.20
$48.45
Custom Tile
The mosaic features 15 conventional quatrefoils that are each inlayed within a singular surrounding tile - an aesthetic that is only possible with waterjet cutting. The tiles are ⅜” (10mm) thick. In total, the project involved 1 hour and 35 minutes of WAZER cut time and used 31 pounds (14kg) of abrasive. Each pair of quatrefoil and surrounding square (of the same color) came from the same tile, so the width of the grout corresponds to the width of WAZER’s cut.
Glass Sculpture
Stained Glass (0.125") (x3)
34 min
11 lbs
$5.44
$17.34
Glass Sculpture
David designed the Pheonix directly with an X-ACTO knife and paper. He took photos of the paper cuts and the team converted them to .DXF files in Photoshop. The entire project took 34 minutes to cut on WAZER and used 11 pounds (5kg) of abrasive.
Penny Necklace
Penny (x50)
60 mins
20 lbs
$9.60
$30.60
Penny Necklace
Stacey is a jeweler and artist who spends a lot of time hand cutting. She cuts intricate shapes in thousands of individual coins for her work, and has been looking for an automated cutting method so she can save her hands and make more jewelry at a lower cost (right now her necklaces sell for $600!). Other solutions were way too expensive, so WAZER was an obvious choice for her. She’s been one of our earliest fans. Check out more of Stacey's work at www.staceyleewebber.com
Bicycle Belt Drive
Aluminum (0.19") Sprockets (x2)
Aluminum (0.0625") Spacer (x1)
Aluminum (0.0625") Rear Frame Coupler (x1)
168 mins
55 lbs
$26.88
$85.86
Bicycle Belt Drive
Designed and built by Cyclist and WAZER Engineer Christian Moore, this custom belt drive was a longtime dream of Christian’s and finally made possible with the help of WAZER. The belt is quieter than a typical chain and is also cleaner, sleeker and does not rust. Christian could not find the right combination of off-the-shelf parts to make this happen - so he had to go custom, and the result is exactly what he wanted.
Custom Knife
D2 Tool Steel (0.16") Knife Blank (x1)
Copper (0.08") Handle Insert (x2)Carbon Fiber (0.08") Handle Insert - small (x4)
Carbon Fiber (0.08") Handle Insert - large (x2
118 mins
39 lbs
$18.88
$60.18
Custom Knife
The knife was made from 4mm-thick D2 tool-steel and the handle from a combination of 2mm copper and carbon fiber sheets. In total the project involved 1 hour 58 minutes of cut time on WAZER a consumed 39 pounds (18kg) of abrasive.
Resources
TIPS & TRICKS
We've learned alot about how WAZER works best. These are our favorite Tips and Tricks.
HOW-TO-VIDEOS
Find all the information you need to safely and properly setup and operate your WAZER.
Materials & Cutting Speed
Still have questions?
Questions about WAZER? Our Sales and Support teams can help answer any question you may have. For more immediate product support, please also review our Resources Section. If you are still having an issue, you can also reach out to the dedicated Technical Support team. We look forward to hearing from you.
Resources
TIPS & TRICKS
We've learned alot about how WAZER works best. These are our favorite Tips and Tricks.
HOW-TO-VIDEOS
Find all the information you need to safely and properly setup and operate your WAZER.
Materials & Cutting Speed
Still have questions?
Questions about WAZER? Our Sales and Support teams can help answer any question you may have. For more immediate product support, please also review our Resources Section. If you are still having an issue, you can also reach out to the dedicated Technical Support team. We look forward to hearing from you.